ONAN 5500 Installation. On a normal ONAN 8-pin wiring harness the cables are labeled from the harness the following:
Here are typical installation directions for the ONAN 5500 Gas/Diesel/Propane with a generator wiring harness that is 8-pin.
Note: For action 7 you will have to purchase 14-gauge electric wire for the run from our ShorePower track to your transfer switch.
STEP ONE:
Turn-off your generator AC circuit breakers to prevent disruption of coast energy solution during testing and installation of ShorePower track.
STEP 2:
Determine the following 4 cables on your own generator wiring harness.
Make use of label or tape to mark each cable and that means you won’t forget which wire is which.
- A – Ground – Brown
- B – Stop – Green
- C – Begin – Red
- E – Run – Orange
The wires are labeled on the harness as follows on a typical ONAN 10-pin wiring harness
- A – Ground
- C – Start
- E – Stop
- F – Run
NOTE: The pin connections above are typical ONAN connections. Not all the ONAN generators have actually the generator that is same harness connections as some might have been changed by the dealer or RV maker. Make certain you have actually precisely identified the 4 cables precisely before proceeding with step three.
STEP THREE:
Connect one Posi-Tap to every regarding the 4 cables identified in step two.
STEP:
Result in the connection through the ShorePower track to your Posi-Taps (wiring harness) according to the wiring diagram supplied.
- Green cable to E AVOID
- Red cable to C BEGIN
- Brown cable to A GROUND
- Orange cable to FRUN
Be sure to link the proper cables to the wiring harness even as we use red-colored cables over and over again.
On our installation picture we utilized wires that are white expand to your harness because of location of y our device. The closer the installation of our device to your wiring harness will assist you to utilize the provided wire that is 4-foot we offer.
ACTION 5:
- Link the wire that is red the ShorePower Monitor (I3) to 1 region of the enable switch making use of the provided Posi-Lock or a crimp connector.
- Connect the next red cable (provided in the zip-lock bag) to another part associated with enable switch. One other end with this wire that is red fundamentally get in touch to your good battery pack terminal.
STEP 6:
- Link the red cable through the enable switch plus the red cable from (L+) from the ShorePower track to your +12 VDC (good battery terminal).
- Link the wire that is blackM) regarding the ShorePower Monitor to ground (any steel in your RV).
STEP 7:
Through the ShorePower Monitor Power Converter ( See diagram that is wiring – Transfer Switch Connection):
You will need 14-gauge stranded electrical cable for the run from our product to your transfer switch.
- Connect (L) on our MeanWell Power Converter to 1 region of the 110 Volts from the transfer switch.
- Connect the (N) on our MeanWell Power Converter into the center connection (common) in the transfer switch
ACTION 8:
The ShorePower track & the MeanWell Power Converter should both have their green light in, if most of the cables, like the cables towards the transfer switch, happen properly linked. .
- To try the machine turn the ENABLE Switch ON and disconnect from coast energy. The green light on the MeanWell is certainly going down and in roughly 20 moments our product will auto-start your generator.
- Let generator run for approximately a moment then re-connect to shore energy and our product will immediately shut-off your generator in more or less seconds that are 10-12. The green light on the MeanWell should come straight straight back on.
SIGNIFICANT NOTE: switching the ALLOW CHANGE On or OFF will not influence the green light on the ShorePower track or MeanWell. Those two light will always be on IF the ShorePower Monitor is properly connect and you have shore power. The ALLOW SWITCH merely allows or disables monitoring.
This is exactly what a typical set-up will appear to be as soon as it is completed. You will see other client installation photos by clicking right right here.
댓글을 남겨주세요
Want to join the discussion?Feel free to contribute!