The Conclusions and Recommendations may be combined or, in long reports, presented in separate sections.

Conclusions and recommendations

If there are not any recommendations to be made as a consequence of the project, call this section just Conclusions.

The Conclusions section sums up one of the keys points of one’s discussion, the essential popular features of your design, or the significant outcomes of the investigation. As the function is always to round from the story of assembling your shed, it will:

• be written to relate straight to the aims of this project as stated within the Introduction
• indicate the extent to that your aims have now been achieved
• summarise the key findings, outcomes or information in your report
• acknowledge limitations and make suggestions for future work (where applicable)
• Highlight the usefulness or significance of one’s work.

The conclusions should relate genuinely to the aims for the work:

The goal of this project is to design a cell phone tower for a suburban location..

The mobile phone tower presented here can be erected safely in a street that is suburban.

It requires a complete part of a maximum of 2m 2 l, and has now the following safety features.

This investigation will review the volume of passengers utilizing the Monash University Clayton-Caulfield inter-campus bus so that you can recommend adjustments towards the service if required.

Analysis of this survey data obtained in this project demonstrates that use of the Clayton-Caulfield inter-campus bus has increased by 24% in the past 5 years. It is suggested that frequency be increased during peak usage.

The Conclusions section below is from a level 2 Civil Engineering Alternative Designs report presenting two designs for a an overpass bridge. Click on the buttons that are coloured look at comments.

Conclusions

Each of the two bridge designs Lecturer’s comment:
An elegant beginning for a Conclusions follows on neatly from the preceding discussion. In this full case, it indicates that the aims for the project have been met. presented in this report fulfil the criteria specified within the project brief. Both designs Lecturer’s comment:
The main findings or outcomes – in this full case the important thing top features of the designs – are then recapped. Incorporate piers that are round piled foundations, that are used since the soil conditions are unknown and perchance unstable. Design 1, a straightforward i-girder that essay writer cheap is composite, gets the benefit of being made from steel and so has longer spans and fewer piers.

Design 2, a beam that is super-T >Design 2 Lecturer’s comment:
The importance of the end result – in cases like this the ultimate recommendation – is obviously stated. is therefore recommended. It offers Lecturer’s comment:
To finish off, the achievement of the project is reinforced. an inexpensive overpass with superior durability, and fully meets certain requirements for the design brief.

Always address limitations and suggest how they might be overcome in future work. The below that is excerpt from the Conclusions of a written report on a project investigating the effect of pulsation on heat transfer in horizontal pipe flow.

Experimental results Lecturer’s comment:
Key conclusions drawn from the project. indicated that pulsed flow without flow reversal had no effect that is significant with steady flow. Preliminary experiments with reversed flow, however, clearly indicated increased heat transfer. This is certainly likely due Lecturer’s comment:
Provide a explanation that is possible notable results, especially unexpected ones. towards the large disturbances into the hydrodynamic boundary layer when the flow changes direction. Further research Lecturer’s comment:
Recommend further research to address any extra work you think would be useful. is advised to determine the utmost enhancement that is achievable.

It must be noted that Lecturer’s comment:
Acknowledge limitations or errors and suggest explanations solutions that are and/or. the experimental results usually do not buy into the theoretical equations. This might be due to the deposits which developed inside the pipe, or even to thermocouple temperature that is inconsistent. Therefore, regular inspection for the test rig is advised.

For an extremely report that is long it really is acceptable to provide the conclusions and recommendations in point form:

The prototype robot courier presented here has been confirmed to manage to delivering documents autonomously in an office environment. It offers demonstrated the next aspects of mobile robotics:

1. Localisation: The Kalman localisation that is filter-based achieved sub-centimeter accuracy under normal operating conditions.
2. Environment modelling: The occupancy map was updated dynamically to incorporate obstacles not included in the original map.
3. Path planning: A distance path that is transform-based using obstacle transforms produced a globally optimal local entrapment-free way to the target.